Best Beard Roller 2020

Beard Growth Roller

BEARD ROLLER

How to Use Beard Roller – Step by Step

By

Derma beard roller have number of small needles in general its have 540 Titanium needless of size from 0.25 mm to 1.0 mm on it that is used to poke your skin, a process called microneedling.

How Microneedling Beard Help in Facial Hair Growth

The idea is that these tiny holes can help your skin produce more collagen, a protein that helps with healthy-looking skin. It can also open up your skin to serums and hydration products. Typically, you use this treatment on your face, though you can use it on other areas of your body, particularly areas that have scarring. Using a derma roller is fairly simple, though you should clean both your skin and the derma roller before and after use.

beard roller Guide

Derma Roller Beard Growth Results

Here are the Some results of using dermaroller at Beard before and after, you can see major growth in facial hair after using beard roller. But it can be vary from skin and person to person.

dermaroller beard before and after
Dermaroller Beard before and after

 

How to use Derma Roller for Beard Growth Complete Guide [Step by Step]

Step 1: Disinfect the beard roller before use

Tiny needles are penetrating your skin, so obviously you want to disinfect those needles first. Soak the roller in 70% isopropyl alcohol. Leave it for 10 minutes.[2]

  • 70% is better than 99% because it doesn’t evaporate as quickly.
  • After it’s soaked for 10 minutes, pull it out, and shake off the excess alcohol. Let it air dry for a few minutes.[3]

Step 2: Wash your skin in warm water

It’s important to start with clean skin. For example, you could use a gentle foaming cleanser for your face to thoroughly clean your skin. Bar soap or shower gel and water for other parts of your body are fine. The point is you need to start with clean skin, and it’s fine to use your typical cleansers

Step 3: Begin with a numbing cream if you prefer

Most people aren’t sensitive to the needles, but if you’re sensitive to pain, you can use a numbing cream first, particularly if you have needles that are 1.0 millimeter or longer. Rub a lidocaine cream into the area, and leave it for 20 minutes before you start rolling.

  • Wipe off any excess cream before you roll.

Step 4: Roll vertically.

Start on one edge of the area. Roll up it from top to bottom, avoiding the eye socket area if you’re doing your face. Lift it up, and roll over the same area again, repeating 6 times in total. Move the beard roller over and repeat. Keep going until you’ve done the whole area
  • If you’re using longer needles, such as 1.0 millimeter or higher, you may see some light bleeding. However, if you notice more than pinpricks of blood, you should stop. You may need a smaller needle.

Step 5: Roll horizontally

Starting at the top or bottom, roll across the area horizontally. Lift up, and roll over the same area again. Roll over it 6 times altogether. Move down or up a little bit, and repeat the process until you’ve done the whole area

  • You can also go diagonally, but that can lead to uneven needling.

Stop rolling after 2 minutes, particularly on your face. You can overdo it with microneedling, especially on your face. Therefore, it’s a good idea to limit each rolling session to under 2 minutes if you can.

Note: Use a derma beard roller every other day or so, Using it too often can lead to inflammation. At most, try using your derma beard roller 3 to 5 times a week, making sure to give your skin a break every now and then. Some people only use this treatment every 6 weeks, for instance.

Final Steps: Rinse your face

After you’re done, rinse off your face. You can just use water, since you’ve already cleansed your face, but you need to remove any blood traces. You can also use a gentle cleanser if you prefer.

Hydrate your skin. It can help to use a hydration product after you’re done. For instance, a sheet mask can help you hydrate and heal. Another option is applying an anti-aging or anti-wrinkle serum after you’re done. These serums will penetrate more deeply because of the micro holes.

Clean the Beard roller in dish soap and water. Wash your beard roller off using dish soap and hot water. Dish soap is better than other soaps at removing the tiny particles of blood and skin on your roller. Put the soap and water in a clean container, and shake the beard roller around in the water.

Disinfect the Beard roller after use. Shake off excess water. Put the Beard roller in 70% isopropyl alcohol. Let it soak for 10 minutes before shaking off the alcohol. Give it a chance to air dry before putting it away.

Source: